P+F 倍加福品牌产品信息介绍-买道传感网官网

商品名称： 6GR6232-3AB00-PF-接近式超声波传感器-P+F 倍加福

商品型号： 6GR6232-3AB00-PF

品牌名： P+F 倍加福

分类：开关传感器

订货号：

类型：接近式超声波传感器

商品名称： P+F 倍加福 UB6000-F42-I-V15 超声波传感器 Diffuse and Retroreflective Mode Sensors

商品型号： UB6000-F42-I-V15

品牌名： P+F 倍加福

分类：测量传感器

订货号：

类型：超声波测距传感器

标准目标板	100 mm x 100 mm
绿色 LED	绿色常亮：通电
UL 认证	cULus 认证，2 类电源
环境温度	-25 ... 70 °C (-13 ... 158 °F)
高度	80 mm
输出类型	1 路模拟量输出 4 ...20 mA
标准	EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003
CCC 认证	额定电压 ≤ 36 V 时，产品不需要 CCC 认证/标记
连接类型	连接器插头 M12 x 1 ， 5 针
外壳	ABS
红色 LED	正常运行：“故障” 程序功能：未检测到物体
响应延迟	大约 650 ms
负载阻抗	0 ...300 Ohm
空载电流	I ≤ 60 mA
工作电压	U 10 ... 30 V DC ，纹波 10 %
质量	210 g
感应范围	350 ... 6000 mm
特性曲线的偏差	± 1 % 满量程值
重复精度	± 0,1 % 满量程值
防护等级	IP54
长度	50 mm
默认设置	评估极限 A1： 400 mm ，评估极限 A2： 6000 mm ，宽声锥
多路转换操作	≤ 7/n Hz，n = 传感器的数量
存储温度	-40 ... 85 °C (-40 ... 185 °F)
同步	双向 0 电平 -U ...+1 V 1 电平：+4 V...+U 输入阻抗：> 12 KOhm 同步脉冲：≥ 100 µs，同步脉冲间歇时间：≥ 2 ms
共模操作	max. 7 Hz
温度影响	± 1 % 满量程值
调整范围	400 ... 6000 mm
死区	0 ... 350 mm
换能器频率	大约 65 kHz
黄色 LED	常亮：物体在评估范围内闪烁：程序功能
分辨率	0,7 mm
换能器	环氧树脂/空心玻璃球混合物；聚氨酯泡沫，盖 PBT
宽度	80 mm

商品名称： IL2301-B110

商品型号： IL2301-B110

品牌名： P+F 倍加福

分类：连接件

订货号：

类型：端子

商品名称： P+F 倍加福 OQT150-R101-2EP-IO-V31-L IO-Link

商品型号： OQT150-R101-2EP-IO-V31-L

品牌名： P+F 倍加福

分类：开关传感器

订货号：

类型：光电传感器

光束发散	> 5 mrad ; 在 50 mm 范围内，d63 < 1 mm ...250 mm
光点直径	大约 2 mm 相距 150 mm
发散角	大约 1 °
调整范围	20 ... 150 mm
黑/白差 (6 %/90 %)	< 3 % 当 150 mm
功能指示灯	黄色 LED：常亮 - 开关输出激活常灭 - 开关输出停用
开关电压	最大 30 V DC
FDA 认证	IEC 60825-1:2007 符合 21 CFR 1040.10 和 1040.11，但存在符合 2007 年 6 月 24 日发布的第 50 号激光通知的偏离情况
使用类别	DC-12 和 DC-13
空载电流	I < 20 mA 在 24 V 供电下
最大脉冲能量	15,2 nJ
环境光限制	EN 60947-5-2 : 30000 Lux
任务时间 (T	) 20 a
控制元件	示教按键
高度	41,4 mm
深度	18,3 mm
设备配置文件	智能传感器
电压降	U ≤ 1,5 V DC
防护等级	IP67 / IP69 / IP69K
光源类型	调制可见红光
开关类型	默认设置为： C/Q - 针脚 4：NPN 常开，PNP 常闭，IO-Link Q2 - 针脚 2：NPN 常开，PNP 常闭
响应时间	2,3 ms
通信接口	IEC 61131-9
参考目标	标准白色平板，100 mm x 100 mm
纹波	最大 10 %
环境温度	-40 ... 60 °C (-40 ... 140 °F)
最大检测范围	8 ... 150 mm
激光安全	EN 60825-1:2014
光学端面	PMMA
SIO 模式支持	是
脉冲长度	3 µs
存储温度	-40 ... 70 °C (-40 ... 158 °F)
外壳	PC（聚碳酸酯）
注意	激光，切勿直视激光束
诊断覆盖率 (DC)	0 %
信号输出	2 路推挽式（4 合 1）输出，短路保护，反极性保护，过电压保护
产品标准	EN 60947-5-2
IO-Link 修正	1.1
设备 ID	0x110802 (1116162)
传输速率	COM 2 (38.4 kb/s)
质量	大约 10 g
最小检测范围	8 ... 20 mm
激光等级	1
波长	680 nm
重复率	大约 3 kHz
连接	M8 x 1 连接器，4 针
宽度	13,9 mm
工作电压	U 10 ... 30 V DC
过程数据位宽	过程数据输入 2 位过程数据输出 2 位
最小循环时间	2,3 ms
兼容主端口类型	A
开关频率	f 217 Hz
UL 认证	E87056 ，通过 cULus 认证， class 2 类供电电源，类型等级 1
检测距离	8 ... 150 mm
光源	激光二极管
MTTF	560 a
工作指示灯	绿色 LED：持续亮起 - 通电闪烁 (4Hz) - 短路闪烁并带有短间歇 (1 Hz) - IO-Link 模式
控制元件_1	5 档旋转开关，用于选择操作模式
开关电流	最大 100 mA ，阻抗负载

商品名称： P+F 倍加福 NBN3-8GM30-E2-V1 电感式传感器

商品型号： NBN3-8GM30-E2-V1

品牌名： P+F 倍加福

分类：开关传感器

订货号：

类型：电感式接近开关

外壳材料	黄铜，镀镍
感应面	LCP
感应距离	3
工作电压	5 ~ 30
输出电路	PNP
直径	8 mm
长度	55 mm
防护等级	IP65 / IP66 / IP67
开关频率	0 ~ 4500
连接方式	连接器插头 M12x4针
工作温度	-40 ~ 85
开关类型	常开 (NO)
螺纹尺寸	55 mm
安装在金属	非齐平

商品名称： P+F 倍加福 KFD2-SOT3-Ex2 SIL-Capable Products for Hazardous Areas Safety Integrity Level 2

商品型号： KFD2-SOT3-EX2

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：隔离栅

Rated voltage	U 30 V DC
Dimensions	20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2
Depth	115 mm
Rated values	acc. to EN 60947-5-6 (NAMUR), see manual for electrical data
Pulse/Pause ratio	min. 100 µs / min. 100 µs
Signal type	Digital Input
Connection	screw terminals
Current	I 17.1 mA
Width	20 mm
Ambient temperature	-20 ... 60 °C (-4 ... 140 °F)
Control drawing	116-0424 (cULus)
Ripple	≤ 10 %
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
IECEx marking	Ex nA [ia Ga] IIC T4 Gc , [Ex ia Da] IIIC , [Ex ia Ma] I
Line fault detection	breakage I ≤ 0.1 mA , short-circuit I ≥ 6.5 mA
Collective error message	Power Rail
Power	P 45 mW (linear characteristic)
Output I	signal ; Transistor
Output II	signal ; Transistor
Rated current	I 100 mA , short-circuit protected
Degree of protection	IP20
Input/Output	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Maximum safe voltage	U 253 V AC (Attention! U is no rated voltage.)
Control elements	DIP switch
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Configuration	via DIP switches
UL approval	E106378
EU-type examination certificate	EXA 16 ATEX 0016 X
Power dissipation	≤ 1.1 W including maximum power dissipation in the output
Display elements	LEDs
IECEx certificate	IECEx EXA 16.0009X
Signal level	1-signal: (external voltage) - 3 V max. for 100 mA 0-signal: blocked output (off-state current ≤ 10 µA)
Input	Ex ia
Response time	≤ 200 µs
Safety Integrity Level (SIL)	SIL 2
Mass	approx. 150 g
Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010
Open circuit voltage/short-circuit current	approx. 10 V DC / approx. 8 mA
Systematic capability (SC)	SC 3
Input/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Voltage	U 10.5 V
Connection side	control side
Switching frequency	≤ 5 kHz
Maximum safe voltage_1	U 253 V AC (Attention! The rated voltage can be lower.)
Mounting	on 35 mm DIN mounting rail acc. to EN 60715:2001
Marking	II 3(1)G Ex nA [ia Ga] IIC T4 Gc [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Labeling	space for labeling at the front
Electromagnetic compatibility	NE 21:2012 , EN 61326-3-2:2008
Height	119 mm
Switching point/switching hysteresis	1.2 ... 2.1 mA / approx. 0.2 mA
Output/power supply	basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 V

商品名称： P+F 倍加福 KFD2-PT2-Ex1-5 本质安全型隔离栅 K-System (DIN rail mounting)

商品型号： KFD2-PT2-EX1-5

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：隔离栅

Configuration	via potentiometer
Degree of protection	IP20
Mounting	on 35 mm DIN mounting rail acc. to EN 60715:2001
Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010
IECEx certificate	IECEx BAS 10.0060 IECEx BAS 10.0061X
Current	I 31.4 mA
Marking_1	II 3G Ex nA II T4
Lead resistance	5 % of the potentiometer resistance (adjustable)
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Ripple	within the supply tolerance
Output/power supply	functional insulation, rated insulation voltage 50 V AC
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
EU-type examination certificate	BAS 00 ATEX 7171
Voltage	U 10.4 V DC
Power	P 82 mW
Current output	4 ... 20 mA, load ≤1 kΩ
Input/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Control drawing_1	116-0173 (cULus)
Power consumption	1.3 W
Accuracy	0.05 %
Protection against electrical shock	UL 61010-1
Power dissipation	1 W
IECEx marking	[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I Ex ec IIC T4 Gc
Maximum safe voltage_1	U 250 V (Attention! The rated voltage can be lower.)
Supply voltage	approx. 4.7 V
Connection	screw terminals
Electromagnetic compatibility	NE 21:2012
Ambient temperature	-20 ... 60 °C (-4 ... 140 °F)
Rise time	10 to 90 % ≤ 8 ms; 10 to 90 % within 1 % of span ≤ 25 ms
Input/Output	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Rated voltage	U 20 ... 35 V DC
Dimensions	20 x 107 x 115 mm (0.8 x 4.2 x 4.5 inch) (W x H x D) , housing type B1
Certificate	TÜV 02 ATEX 1797 X
Control drawing	116-0129
Influence of ambient temperature	≤ 1 µA/K
Types of measuring	3-, 4-, 5-wire technology
Control elements	potentiometer
Mass	approx. 120 g
Marking	II (1)G [Ex ia Ga] IIC , [exsign] II (1)D [Ex ia Da] IIIC , [exsign] I (M1) [Ex ia Ma] I
Signal type	Analog input
Connection side	control side
Maximum safe voltage	U 250 V (Attention! The rated voltage can be lower.)
Nominal resistance	800 Ω to 100 kΩ
Linearity	± 10 µA

商品名称： P+F 倍加福 KFD2-GUT-1.D 信号调节器 K-System (DIN rail, highly functional)

商品型号： KFD2-GUT-1.D

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：隔离栅

Load	max. 650 Ω
Electromagnetic compatibility	NE 21:2007
Voltage	0.1 % of span
Current output	max. 20 µA
Safety Integrity Level (SIL)	SIL 2
Labeling	space for labeling at the front
Width	40 mm
Fault signal	downscale I ≤ 3.6 mA, upscale I ≥ 21 mA (acc. NAMUR NE43)
Configuration	via operating buttons via PACTware
Directive 2014/35/EU	EN 61010-1:2010
Output I, II/other circuits	reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V
Dimensions	40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) (W x H x D) , housing type C2
Programming interface	programming socket
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Ambient temperature	-20 ... 60 °C (-4 ... 140 °F)
RTD	max. 0.2 % of span
Measurement loop monitoring_1	sensor breakage
Connection	screw terminals
Thermocouples	max. 10µV deviation of CJC: ±0.8 K
Rated voltage	U 20 ... 30 V DC
Display elements	LEDs , display
Mass	300 g
Depth	115 mm
Mounting	on 35 mm DIN mounting rail acc. to EN 60715:2001
Types of measuring_1	2-, 3-, 5-wire technology
Cold junction compensation	external and internal
Power dissipation/power consumption	≤ 2 W / 2.2 W
Output I, II	relay
Output III	Analog current output
Connection side	control side
Measurement loop monitoring	sensor breakage, sensor short-circuit
Potentiometer	0.1 % of span when < 5 kΩ 0.5 % of span when > 5 kΩ
Energized/De-energized delay	approx. 20 ms / approx. 20 ms
Input resistance	≥ 250 kΩ (0 ... 10 V) min. 1 MΩ (0 ... 1 V, -100 ... 100 mV)
Types of measuring	2-, 3-, 4-wire technology
Rated current	I approx. 100 mA
Current range	0 ... 20 mA or 4 ... 20 mA
Collective error message	Power Rail
Output III/power supply and collective error	reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V
Interface/power supply	reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V
Height	119 mm
Contact loading	250 V AC / 2 A / cos φ ≥ 0.7 ; 40 DC / 2 A
Temperature effect	Input: 0.005 %/K (50 ppm) of span ; current output: 0.005 %/K (50 ppm) of span
Sampling rate	approx. 700 ms
Signal type	Analog input
Degree of protection	IP20
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Measuring current	approx. 400 µA
Lead resistance	max. 50 Ω
Input/Other circuits	reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V
Mechanical life	5 x 10 switching cycles
Open loop voltage	max. 24 V DC
Output I, II against eachother	reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V

商品名称： P+F 倍加福 Z728 齐纳防爆栅模块

商品型号： Z728

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：隔离栅

Relative humidity	max. 75 % , without condensation
Width	12.5 mm
Marking_1	II 3G Ex nA IIC T4 Gc
Marking	II (1)GD, I (M1) [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I
Current	I 93 mA
Maximum safe voltage	U 250 V
Series resistance	min. 301 Ω
Dimensions	12.5 x 115 x 116 mm (0.5 x 4.5 x 4.6 inch) (W x H x D)
Power	P 650 mW
Measurement loop	max. 26.5 V at 10 µA
Height	115 mm
Control drawing	116-0118
Connection	screw terminals
Supply loop	max. 26.9 V
Core cross section	max. 2 x 2.5 ... mm
Mounting	on 35 mm DIN mounting rail acc. to EN 60715:2001
Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010
Degree of protection	IP20
Control drawing_1	116-0139 (cULus)
Type	DC version, positive polarity
Nominal resistance	300 Ω
Storage temperature	-25 ... 70 °C (-13 ... 158 °F)
Mass	approx. 150 g
Voltage	U 28 V
Certificate	TÜV 99 ATEX 1484 X
Depth	116 mm
Construction type	modular terminal housing , see system description
EU-type examination certificate	BAS 01 ATEX 7005
Fuse rating	50 mA
Ambient temperature	-20 ... 60 °C (-4 ... 140 °F)
IECEx certificate	IECEx BAS 09.0142 IECEx BAS 17.0091X
IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.

商品名称： P+F 倍加福 K-LB-2.6 SIL-Capable Products for Hazardous Areas Safety Integrity Level 3

商品型号： K-LB-2.6

品牌名： P+F 倍加福

分类：其他(中低压配电)

订货号：

类型：浪涌保护器

Number of protected signal lines	4
Ambient temperature	-30 ... 80 °C (-22 ... 176 °F) For usage in hazardous area observe the EC-type examination certificate.
Topology	non-grounded
Impulse discharge current (10/350 µs)	I 2 kA per line (2x)
Impulse reset time	< 30 ms
Safety Integrity Level (SIL)	SIL 3
Degree of protection	IP20
Mass	approx. 100 g
Current	I 250 mA
Certificate	PF 16 CERT 4065 X
Depth	116 mm
Internal capacitance	C negligible
Internal inductance	L 200 µH
Relative humidity	5 ... 95 %
Marking	II 2(1)G Ex ia IIC T6/T5/T4
Marking_1	II (3)D [Ex ic Dc] IIIC
Nominal discharge current (8/20 µs)	I 5 kA per line (10x)
Surge protective devices for low voltage	EN 61643-21:2001+A1:2009+A2:2013 IEC 61643-21:2001+A1:2008+A2:2012
Temperature class	T6 for ambient temperature ≤ 50 °C T5 for ambient temperature ≤ 70 °C T4 for ambient temperature ≤ 80 °C
Rated current	I 250 mA
Dimensions	12.5 x 115 x 116 mm (0.5 x 4.5 x 4.6 inch) (W x H x D)
Voltage	U 6 V
Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012
Width	12.5 mm
Nominal voltage	1 V DC
Leakage current	< 5 µA at 1 V and 25 °C (77 °F) , line-line
Connection	screw terminals
Series resistance	< 0.5 Ω per line
Core cross section	2 x 2.5 mm
Total discharge current (8/20 µs)	I 20 kA (1x)
Mounting	on 35 mm DIN mounting rail acc. to EN 60715:2001
EU-type examination certificate	PTB 00 ATEX 2176 X
Impulse rating	10 kV/5 kA (category C2) 2 kV/2 kA (category D1)
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Labeling	space for labeling at the front
IECEx certificate	IECEx BAS 14.0010X
Height	115 mm
Rated surge current (8/20 µs)	I 10 kA per line (1x)
Control drawing	116-0187 (cCSAus)
Maximum continuous operating voltage	U 6 V DC
Voltage protection level	U max. 60 V line-line for nominal discharge current I max. 1.2 kV line-earth for nominal discharge current I
Insertion loss	≤ 0.05 dB, at 0 ... 4 kHz, in 600 Ω-System ≤ 3 dB, at 0 ... 174 kHz, in 100 Ω-System
Mounting location	indoor