买道传感网

分类

P+F 倍加福品牌产品信息介绍-买道传感网官网

P+F 倍加福 KFU8-SR-Ex1.W.LB SIL-Capable Products for Hazardous Areas Safety Integrity Level 2

商品名称: P+F 倍加福 KFU8-SR-Ex1.W.LB SIL-Capable Products for Hazardous Areas Safety Integrity Level 2

商品型号: KFU8-SR-EX1.W.LB

品牌名: P+F 倍加福

分类: 其他过程测量仪表

订货号:

类型: 开关放大器

Connection side control side
Mechanical life 10 switching cycles
Safety Integrity Level (SIL) SIL 2
Ambient temperature -40 ... 60 °C (-40 ... 140 °F) extended ambient temperature range up to 70 °C (158 °F), refer to manual for necessary mounting conditions
Marking II 3(1)G Ex ec nC [ia Ga] IIC T4 Gc [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Connection screw terminals
Contact loading 250 V AC/2 A/cos φ > 0.75; 126.5 V AC/4 A/cos φ > 0.75; 30 V DC/2 A resistive load
Labeling space for labeling at the front
IECEx marking Ex ec nC [ia Ga] IIC T4 Gc , [Ex ia Da] IIIC , [Ex ia Ma] I
Open circuit voltage/short-circuit current approx. 8 V DC / approx. 8 mA
Rated values acc. to EN 60947-5-6 (NAMUR)
Switching point/switching hysteresis 1.2 ... 2.1 mA / approx. 0.2 mA
Output II signal or fault message ; relay
Minimum switch current 2 mA / 24 V DC
Degree of protection IP20
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Switching frequency ≤ 10 Hz
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Power dissipation/power consumption ≤ 1.2 W / ≤ 1.2 W ; 3.4 VA
Systematic capability (SC) SC 3
Output/power supply reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V
Mass approx. 150 g
Mounting on 35 mm DIN mounting rail acc. to EN 60715:2001
Energized/De-energized delay approx. 20 ms / approx. 20 ms
Electromagnetic compatibility NE 21:2017 , EN 61326-3-1:2017 , EN IEC 61326-3-2:2018 , EN IEC 61326-1:2021 (industrial locations)
Maximum safe voltage_1 U 253 V AC (Attention! The rated voltage can be lower.)
Output I signal ; relay
Directive 2014/34/EU EN IEC 60079-0:2018 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012 , EN IEC 60079-15:2019
Output/Output reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V
IECEx certificate IECEx FIDI 22.0003X
Input/power supply safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Voltage U 10.5 V
Control drawing 116-0489
Input/Output safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Maximum safe voltage U 253 V AC (Attention! U is no rated voltage.)
Configuration via DIP switches
Input Ex ia
Height 119 mm
Width 20 mm
Pulse/Pause ratio min. 20 ms / min. 20 ms
EU-type examination certificate FIDI 22 ATEX 0029 X
Display elements LEDs
UL approval E106378
Power P 34 mW (linear characteristic)
Rated voltage U 19 ... 30 V DC / 90 ... 253 V AC 50 ... 60 Hz
Dimensions 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2
Directive 2014/35/EU EN 61010-1:2010+A1:2019+A1:2019/AC:2019
Control elements DIP switch
Depth 115 mm
Signal type Digital Input
Current I 13 mA
Line fault detection breakage I ≤ 0.1 mA , short-circuit I > 6 mA
P+F 倍加福 NBB2-8GM50-E2 电感式传感器

商品名称: P+F 倍加福 NBB2-8GM50-E2 电感式传感器

商品型号: NBB2-8GM50-E2

品牌名: P+F 倍加福

分类: 测量传感器

订货号:

类型: 电感式接近传感器

感应距离 2
外壳材料 黄铜,镀镍
安装在金属 齐平
工作电压 5 ~ 30
防护等级 IP65 / IP66 / IP67
开关频率 0 ~ 6000
长度 L 2 m
连接方式 电缆
工作温度 -40 ~ 85
输出电路 PNP
开关类型 常开 (NO)
感应面 LCP
直径 8 mm
螺纹尺寸 L 2 m
ENA58IL-S10CA5-0013B17-ABP P+F 倍加福 运动控制传感器

商品名称: ENA58IL-S10CA5-0013B17-ABP P+F 倍加福 运动控制传感器

商品型号: ENA58IL-S10CA5-0013B17-ABP

品牌名: P+F 倍加福

分类: 运动控制传感器

订货号:

类型: 绝对值编码器

IQC22-C1 P+F 倍加福 其它(传感器)

商品名称: IQC22-C1 P+F 倍加福 其它(传感器)

商品型号: IQC22-C1

品牌名: P+F 倍加福

分类: 其它(传感器)

订货号:

类型: RFID读/写头和电子标签

ENI58IL-S10CA5-1024UD2-RC2

商品名称: ENI58IL-S10CA5-1024UD2-RC2

商品型号: ENI58IL-S10CA5-1024UD2-RC2

品牌名: P+F 倍加福

分类: 运动控制传感器

订货号:

类型: 增量式编码器

P+F 倍加福 OQT150-R101-2EP-IO-V31-L IO-Link

商品名称: P+F 倍加福 OQT150-R101-2EP-IO-V31-L IO-Link

商品型号: OQT150-R101-2EP-IO-V31-L

品牌名: P+F 倍加福

分类: 开关传感器

订货号:

类型: 光电传感器

光束发散 > 5 mrad ; 在 50 mm 范围内,d63 < 1 mm ...250 mm
光点直径 大约 2 mm 相距 150 mm
发散角 大约 1 °
调整范围 20 ... 150 mm
黑/白差 (6 %/90 %) < 3 % 当 150 mm
功能指示灯 黄色 LED: 常亮 - 开关输出激活 常灭 - 开关输出停用
开关电压 最大 30 V DC
FDA 认证 IEC 60825-1:2007 符合 21 CFR 1040.10 和 1040.11,但存在符合 2007 年 6 月 24 日发布的第 50 号激光通知的偏离情况
使用类别 DC-12 和 DC-13
空载电流 I < 20 mA 在 24 V 供电下
最大脉冲能量 15,2 nJ
环境光限制 EN 60947-5-2 : 30000 Lux
任务时间 (T ) 20 a
控制元件 示教按键
高度 41,4 mm
深度 18,3 mm
设备配置文件 智能传感器
电压降 U ≤ 1,5 V DC
防护等级 IP67 / IP69 / IP69K
光源类型 调制可见红光
开关类型 默认设置为: C/Q - 针脚 4:NPN 常开,PNP 常闭,IO-Link Q2 - 针脚 2:NPN 常开,PNP 常闭
响应时间 2,3 ms
通信接口 IEC 61131-9
参考目标 标准白色平板,100 mm x 100 mm
纹波 最大 10 %
环境温度 -40 ... 60 °C (-40 ... 140 °F)
最大检测范围 8 ... 150 mm
激光安全 EN 60825-1:2014
光学端面 PMMA
SIO 模式支持
脉冲长度 3 µs
存储温度 -40 ... 70 °C (-40 ... 158 °F)
外壳 PC(聚碳酸酯)
注意 激光 , 切勿直视激光束
诊断覆盖率 (DC) 0 %
信号输出 2 路推挽式(4 合 1)输出,短路保护,反极性保护,过电压保护
产品标准 EN 60947-5-2
IO-Link 修正 1.1
设备 ID 0x110802 (1116162)
传输速率 COM 2 (38.4 kb/s)
质量 大约 10 g
最小检测范围 8 ... 20 mm
激光等级 1
波长 680 nm
重复率 大约 3 kHz
连接 M8 x 1 连接器,4 针
宽度 13,9 mm
工作电压 U 10 ... 30 V DC
过程数据位宽 过程数据输入 2 位 过程数据输出 2 位
最小循环时间 2,3 ms
兼容主端口类型 A
开关频率 f 217 Hz
UL 认证 E87056 , 通过 cULus 认证 , class 2 类供电电源 , 类型等级 1
检测距离 8 ... 150 mm
光源 激光二极管
MTTF 560 a
工作指示灯 绿色 LED: 持续亮起 - 通电 闪烁 (4Hz) - 短路 闪烁并带有短间歇 (1 Hz) - IO-Link 模式
控制元件_1 5 档旋转开关,用于选择操作模式
开关电流 最大 100 mA , 阻抗负载
P+F 倍加福 NBN3-8GM30-E2-V1 电感式传感器

商品名称: P+F 倍加福 NBN3-8GM30-E2-V1 电感式传感器

商品型号: NBN3-8GM30-E2-V1

品牌名: P+F 倍加福

分类: 开关传感器

订货号:

类型: 电感式接近开关

外壳材料 黄铜,镀镍
感应面 LCP
感应距离 3
工作电压 5 ~ 30
输出电路 PNP
直径 8 mm
长度 55 mm
防护等级 IP65 / IP66 / IP67
开关频率 0 ~ 4500
连接方式 连接器插头 M12x4针
工作温度 -40 ~ 85
开关类型 常开 (NO)
螺纹尺寸 55 mm
安装在金属 非齐平
ENI58IL-H12DA5-1024UD1-RBE

商品名称: ENI58IL-H12DA5-1024UD1-RBE

商品型号: ENI58IL-H12DA5-1024UD1-RBE

品牌名: P+F 倍加福

分类: 其他

订货号:

类型: 其他

V1-W-N4-15M-PUR-N4S

商品名称: V1-W-N4-15M-PUR-N4S

商品型号: V1-W-N4-15M-PUR-N4S

品牌名: P+F 倍加福

分类: 连接件

订货号:

类型: 连接线缆

P+F 倍加福 KFD2-SOT3-Ex2 SIL-Capable Products for Hazardous Areas Safety Integrity Level 2

商品名称: P+F 倍加福 KFD2-SOT3-Ex2 SIL-Capable Products for Hazardous Areas Safety Integrity Level 2

商品型号: KFD2-SOT3-EX2

品牌名: P+F 倍加福

分类: 安全传感器

订货号:

类型: 隔离栅

Rated voltage U 30 V DC
Dimensions 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2
Depth 115 mm
Rated values acc. to EN 60947-5-6 (NAMUR), see manual for electrical data
Pulse/Pause ratio min. 100 µs / min. 100 µs
Signal type Digital Input
Connection screw terminals
Current I 17.1 mA
Width 20 mm
Ambient temperature -20 ... 60 °C (-4 ... 140 °F)
Control drawing 116-0424 (cULus)
Ripple ≤ 10 %
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
IECEx marking Ex nA [ia Ga] IIC T4 Gc , [Ex ia Da] IIIC , [Ex ia Ma] I
Line fault detection breakage I ≤ 0.1 mA , short-circuit I ≥ 6.5 mA
Collective error message Power Rail
Power P 45 mW (linear characteristic)
Output I signal ; Transistor
Output II signal ; Transistor
Rated current I 100 mA , short-circuit protected
Degree of protection IP20
Input/Output safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Maximum safe voltage U 253 V AC (Attention! U is no rated voltage.)
Control elements DIP switch
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Configuration via DIP switches
UL approval E106378
EU-type examination certificate EXA 16 ATEX 0016 X
Power dissipation ≤ 1.1 W including maximum power dissipation in the output
Display elements LEDs
IECEx certificate IECEx EXA 16.0009X
Signal level 1-signal: (external voltage) - 3 V max. for 100 mA 0-signal: blocked output (off-state current ≤ 10 µA)
Input Ex ia
Response time ≤ 200 µs
Safety Integrity Level (SIL) SIL 2
Mass approx. 150 g
Directive 2014/34/EU EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010
Open circuit voltage/short-circuit current approx. 10 V DC / approx. 8 mA
Systematic capability (SC) SC 3
Input/power supply safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Voltage U 10.5 V
Connection side control side
Switching frequency ≤ 5 kHz
Maximum safe voltage_1 U 253 V AC (Attention! The rated voltage can be lower.)
Mounting on 35 mm DIN mounting rail acc. to EN 60715:2001
Marking II 3(1)G Ex nA [ia Ga] IIC T4 Gc [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Labeling space for labeling at the front
Electromagnetic compatibility NE 21:2012 , EN 61326-3-2:2008
Height 119 mm
Switching point/switching hysteresis 1.2 ... 2.1 mA / approx. 0.2 mA
Output/power supply basic insulation according to IEC/EN 61010-1, rated insulation voltage 300 V