买道传感网

分类

中低压配电品牌厂家-买道传感网官网

P+F 倍加福 CJ4-12GK-N-10M Sensors for Hazardous Areas 电容式传感器

商品名称: P+F 倍加福 CJ4-12GK-N-10M Sensors for Hazardous Areas 电容式传感器

商品型号: CJ4-12GK-N-10M

品牌名: P+F 倍加福

分类: 开关传感器

订货号:

类型: 电容式接近开关

额定电压 U 8 V
未检测到测量板 max. 1 mA
设备保护级别 Ga IECEx TUN 20.0014X
UL 认证 cULus 认证,一般用途
连接类型 电缆
C 12 mm
NAMUR EN 60947-5-6:2000 IEC 60947-5-6:1999
长度 L 10 m
MTTF 3299 a
感应面 PBT
确保操作距离 s 0 ... 2,88 mm
设备保护级别 Da IECEx TUN 20.0014X
设备保护级别 Ga_1 TüV 03 ATEX 2003 X
环境温度 -25 ... 70 °C (-13 ... 158 °F)
在危险区域使用: 参见使用说明书
长度_1 60 mm
工作电压 U 7 ... 12 V
输出类型 NAMUR
标准 EN IEC 60947-5-2
设备保护级别 Da_1 TüV 03 ATEX 2003 X
控制图 116-0165
输出类型_1 2 线
开关频率 f 0 ... 1 Hz
防护等级 IP68
额定工作距离 s 4 mm
检测到测量板 ≥ 2,4 mA
外壳材料 PBT
弯曲半径 > 10 x 缆线直径
F 70 mm
安装 非齐平
设备保护级别 Gb IECEx TUN 20.0014X
电缆直径 4,8 mm ± 0,2 mm
材料 PVC
B 80 mm
开关功能 常开 (NO)
设备保护级别 Gb_1 TüV 03 ATEX 2003 X
线芯横截面积 0,34 mm
直径 12 mm
任务时间 (T ) 20 a
诊断覆盖率 (DC) 0 %
A 20 mm
P+F 倍加福 KC-CJC-1GN 信号调节器 K-System (DIN rail, highly functional)

商品名称: P+F 倍加福 KC-CJC-1GN 信号调节器 K-System (DIN rail, highly functional)

商品型号: KC-CJC-1GN

品牌名: P+F 倍加福

分类: 温湿度产品

订货号:

类型: 温度计

Mass approx. 15 g
Dimensions 23 x 10 x 17 mm (0.9 x 0.4 x 0.67 inch)
P+F 倍加福 KCD2-ST-1.LB 信号调节器 K-System (DIN rail, highly functional)

商品名称: P+F 倍加福 KCD2-ST-1.LB 信号调节器 K-System (DIN rail, highly functional)

商品型号: KCD2-ST-1.LB

品牌名: P+F 倍加福

分类: 安全传感器

订货号:

类型: 隔离栅

Protection against electrical shock IEC 61010-1:2010
Height 119 mm
Line fault detection breakage I ≤ 0.1 mA , short-circuit I ≥ 6.5 mA
Connection screw terminals
Input/power supply reinforced insulation acc. to EN 50178, rated insulation voltage 300 V
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Degree of protection IP20
Ambient temperature -20 ... 60 °C (-4 ... 140 °F) extended ambient temperature range up to 70 °C (158 °F), refer to manual for necessary mounting conditions
Mass approx. 100 g
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Configuration via DIP switches
Output/power supply not available , common pole terminal 9+
Display elements LEDs
Depth 114 mm
Mounting on 35 mm DIN mounting rail acc. to EN 60715:2001
Rated values acc. to EN 60947-5-6 (NAMUR)
Rated voltage U 30 V DC
Connection side control side
Labeling space for labeling at the front
Collective error message Power Rail
Output I signal ; Transistor
Response time ≤ 200 µs
Signal type Digital Input
Width 12.5 mm
Switching frequency ≤ 5 kHz
Output II signal or fault message ; Transistor
Ripple ≤ 10 %
Input/Output reinforced insulation acc. to EN 50178, rated insulation voltage 300 V
Safety Integrity Level (SIL) SIL 2
Systematic capability (SC) SC 3
Power dissipation ≤ 700 mW including maximum power dissipation in the output
Output/Output not available , common pole terminal 9+
Electromagnetic compatibility NE 21:2011
Dimensions 12.5 x 119 x 114 mm (0.5 x 4.7 x 4.5 inch) (W x H x D) , housing type A2
Signal level 1-signal: (supply voltage) - 3 V max. for 50 mA 0-signal: blocked output (off-state current ≤ 10 µA)
Input EN 60947-5-6:2000
Open circuit voltage/short-circuit current approx. 10 V DC / approx. 8 mA
Rated current I 50 mA
Switching point/switching hysteresis 1.2 ... 2.1 mA / approx. 0.2 mA
Pulse/Pause ratio min. 100 µs / min. 100 µs
P+F 倍加福 HiC5861 本质安全型隔离栅 H-System (Termination Board mounting)

商品名称: P+F 倍加福 HiC5861 本质安全型隔离栅 H-System (Termination Board mounting)

商品型号: HiC5861

品牌名: P+F 倍加福

分类: 继电器

订货号:

类型: 继电器

UL approval E106378
Minimum switch current 10 mA / 24 V DC
Fuse rating 1.5 A
Degree of protection IP20
Dimensions 12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D)
Marking II 3G Ex nC ec IIC T4 Gc
Coding no pin trimmed For further information see system description.
Power dissipation < 1.3 W
Energized/De-energized delay 150 ms / 150 ms
Certificate PF 17 CERT 4192 X
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Rated current I 0-signal: typ. 1.6 mA at 1.5 V DC; typ. 8 mA at 3 V DC (maximum leakage current DO card) 1-signal: ≥ 36 mA (minimum load current DO card)
Output/Output reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 253 V
Signal level 0-signal: -5 ... 5 V 1-signal: 19 ... 27.6 V
Rated voltage U 19 ... 27.6 V loop powered
Mounting on termination board
Connection side field side
Performance level (PL) PL e
Contact loading 30 V DC/1 A resistive load
Electromagnetic compatibility NE 21:2012 , EN 61326-3-1:2008 , EN 61326-3-2:2008
Mass approx. 100 g
Directive 2014/35/EU EN 61010-1:2010
Mechanical life 2 x 10 switching cycles
Test pulse length max. 4 ms from DO card
Labeling space for labeling at the front
Input/Output reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 253 V
Safety Integrity Level (SIL) SIL 3
Test input see functional safety manual
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Ambient temperature -20 ... 60 °C (-4 ... 140 °F) Observe the temperature range limited by derating, see section derating.
Height 106 mm
Width 12.5 mm
Depth 128 mm
Switching frequency < 3 Hz
Power consumption < 1.3 W
Connection SL2: 5a, 5b
Pulse/Pause ratio 150 ms / 150 ms
Directive 2006/42/EC EN 62061:2005 , EN/ISO 13849-1:2008
Directive 2014/34/EU EN 60079-0:2012+A11:2013 , EN 60079-7:2015 , EN 60079-15:2010
Signal type Digital Output
Display elements LEDs
P+F 倍加福 KFD0-CS-Ex1.54-Y2 本质安全型隔离栅 K-System (DIN rail mounting)

商品名称: P+F 倍加福 KFD0-CS-Ex1.54-Y2 本质安全型隔离栅 K-System (DIN rail mounting)

商品型号: KFD0-CS-Ex1.54-Y2

品牌名: P+F 倍加福

分类: 安全传感器

订货号:

类型: 安全栅

Voltage U 25.2 V
Control drawing_1 116-0348 (cULus)
Protection against electrical shock UL 61010-1
Ambient temperature -20 ... 60 °C (-4 ... 140 °F)
Input/Output safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Connection screw terminals
Labeling space for labeling at the front
Height 107 mm
Marking_1 II 3G Ex nA II T4
Influence of ambient temperature ± 20 µA / K
Short-circuit current ≤ 43 mA
Electromagnetic compatibility NE 21:2006
Certificate TÜV 99 ATEX 1499 X
IECEx marking [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex nA IIC T4 Gc
Signal type Analog input
Depth 115 mm
Mass approx. 100 g
Dimensions 20 x 107 x 115 mm (0.8 x 4.2 x 4.5 inch) (W x H x D) , housing type B1
Rise time/fall time ≤ 50 µs (load current ≥ 1 mA)
Rated voltage U 0 ... 24 V DC , loop powered
Marking II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Directive 2014/34/EU EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010
IECEx certificate IECEx BAS 08.0079 IECEx BAS 10.0007X
Transmission range current: 1 ... 20 mA voltage: 0 ... 24 V
Degree of protection IP20
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
After calibration ≤ 3.5 mA current loss at 20 mA load current
Current I 43 mA
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
UL approval E106378
Width 20 mm
Maximum safe voltage U 250 V (Attention! The rated voltage can be lower.)
Power dissipation 0.2 W
Mounting on 35 mm DIN mounting rail acc. to EN 60715:2001
EU-type examination certificate BAS 00 ATEX 7087
Control drawing 116-0129 (cFMus)
Power P 271 mW
P+F 倍加福 KFD2-ER-Ex1.W.LB 本质安全型隔离栅 K-System (DIN rail mounting)

商品名称: P+F 倍加福 KFD2-ER-Ex1.W.LB 本质安全型隔离栅 K-System (DIN rail mounting)

商品型号: KFD2-ER-EX1.W.LB

品牌名: P+F 倍加福

分类: 安全传感器

订货号:

类型: 隔离栅

Configuration via DIP switches via potentiometer
Electromagnetic compatibility NE 21:2006
Mass approx. 150 g
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Input [EEx ia] IIC
Ambient temperature -20 ... 60 °C (-4 ... 140 °F)
Directive 2014/35/EU EN 61010-1:2010
Switching power max. 192 W , 2000 VA
Degree of protection IP20
Marking II (1)G [EEx ia] IIC [circuit(s) in zone 0/1/2]
Height 119 mm
Time constant for signal damping 0.5 s, 2 s, 5 s, 10 s
Directive 2014/34/EU EN 60079-0:2012+A11:2013, EN 60079-11:2012
Output/power supply reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V
Output signal ; relay
Response sensitivity 1 ... 150 kΩ , adjustable via potentiometer
Rated voltage U 20 ... 30 V DC
Control elements DIP switch potentiometer
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Mounting on 35 mm DIN mounting rail acc. to EN 60715:2001
Maximum safe voltage U 40 V DC (Attention! U is no rated voltage.)
Current I 2.5 mA
Power P 6 mW
Input/power supply safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Labeling space for labeling at the front
Signal type Digital Input
Width 20 mm
Voltage U 10 V
Rated current I 30 ... 40 mA
Contact loading 253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load
Dimensions 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2
Input/Output safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
EU-type examination certificate DMT 00 ATEX E 033
Control input min./max. control system: terminals 1, 2, 3 on/off control system: terminals 1, 3
Connection screw terminals , max. 2.5 mm
Display elements LEDs
Connection side control side
Depth 115 mm
P+F 倍加福 KFD2-EB2.SP 本质安全型隔离栅 K-System (DIN rail mounting)

商品名称: P+F 倍加福 KFD2-EB2.SP 本质安全型隔离栅 K-System (DIN rail mounting)

商品型号: KFD2-EB2.SP

品牌名: P+F 倍加福

分类: 安全传感器

订货号:

类型: 隔离栅

Mounting on 35 mm DIN mounting rail acc. to EN 60715:2001
Fusing 5 AT/250 V AC recommended maximum utilization of the fuse: 80 %
Labeling space for labeling at the front
Directive 2014/34/EU EN IEC 60079-0:2018+AC:2020 , EN IEC 60079-7:2015+A1:2018 , EN IEC 60079-15:2019
Rated voltage U 20 ... 30 V DC The maximum rated operating voltage of the devices plugged onto the Power Rail must not be exceeded.
Display elements LEDs
Configuration via DIP switches
IECEx certificate IECEx UL 16.0051X
IECEx marking Ex ec nC IIC T4 Gc
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Electromagnetic compatibility NE 21:2017
Degree of protection IP20
Output voltage U ≥ rated voltage U = U - 0.6 V
Control elements DIP switch
Ambient temperature -40 ... 70 °C (-40 ... 158 °F)
Dimensions 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2
UL approval E106378
Fault signal relay output: NO contact
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Certificate UL 22 ATEX 2853 X
Marking II 3G Ex ec nC IIC T4 Gc
Contact loading 30 V AC/ 2 A / cos φ ≥ 0.7 ; 40 V DC/ 2 A
Energized/De-energized delay approx. 20 ms / approx. 20 ms
Power dissipation ≤ 1 W
Output current max. 4 A
FM approval FM 22 US 0031 X
Control drawing 116-0160
Connection spring terminals
Mass approx. 100 g
CSA approval CoC 1051840
P+F 倍加福 KFD2-ER-2.W.LB 信号调节器 K-System (DIN rail, highly functional)

商品名称: P+F 倍加福 KFD2-ER-2.W.LB 信号调节器 K-System (DIN rail, highly functional)

商品型号: KFD2-ER-2.W.LB

品牌名: P+F 倍加福

分类: 安全传感器

订货号:

类型: 隔离栅

Labeling space for labeling at the front
Electromagnetic compatibility NE 21:2006
Width 20 mm
Depth 115 mm
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Configuration via DIP switches via potentiometer
Control input min./max. control system: terminals 1, 2, 3; 4, 5. 6 on/off control system: terminals 1, 3; 4, 6
Directive 2004/108/EC EN 61326-1:2006
Rated voltage U 20 ... 30 V DC
Input/Output basic insulation according to EN 50178, rated insulation voltage 253 V
Mass approx. 150 g
Signal type Digital Input
Display elements LEDs
Dimensions 20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2
Input/power supply basic insulation according to EN 50178, rated insulation voltage 253 V
Ambient temperature -20 ... 60 °C (-4 ... 140 °F) extended ambient temperature range up to 70 °C (158 °F), refer to manual for necessary mounting conditions
Connection screw terminals , max. 2.5 mm
Mounting on 35 mm DIN mounting rail acc. to EN 60715:2001
Height 119 mm
Output relay
Contact loading 253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load
Rated current I 30 ... 40 mA
Output/power supply basic insulation according to EN 50178, rated insulation voltage 253 V
Degree of protection IP20
Galvanic isolation EN 50178:1997
Response sensitivity 1 ... 150 kΩ , adjustable via potentiometer
Switching power max. 192 W , 2000 VA
Time constant for signal damping 0.5 s, 2 s, 5 s, 10 s
Connection side control side
Insulation coordination EN 50178:1997
Directive 2006/95/EC EN 50178:1997
P+F 倍加福 K-ADP-USB 本质安全型隔离栅 K-System (DIN rail mounting)

商品名称: P+F 倍加福 K-ADP-USB 本质安全型隔离栅 K-System (DIN rail mounting)

商品型号: K-ADP-USB

品牌名: P+F 倍加福

分类: 传感器附件

订货号:

类型: 电缆及适配器

Computer 1 x Type A USB
Mass 85 g
Device 1 x connector 3.5 mm and 3.55 mm
Cable length 3 m
Ambient temperature -20 ... 60 °C (-4 ... 140 °F)
Galvanic isolation functional insulation acc. to IEC 62103, rated insulation voltage 50 V
Directive 2014/30/EU EN 61000-3-2:2014 EN 61000-3-3:2013 EN 61000-4-2:2009 EN IEC 61000-4-3:2020 EN 61000-4-4:2012 EN 61000-4-6:2014 EN 61000-4-8:2010 EN 55032:2015+A11:2020
Current consumption 50 mA (via USB)
P+F 倍加福 PCV80S-F200-SSI-V19 Vision Sensors 定位系统

商品名称: P+F 倍加福 PCV80S-F200-SSI-V19 Vision Sensors 定位系统

商品型号: PCV80S-F200-SSI-V19

品牌名: P+F 倍加福

分类: 视觉传感器

订货号:

类型: 读码器

数字分辨率 32 Bit
“常开位置”X 值 0
数据内容 X 位置 , 状态
类型 CMOS , 全局快门
空载电流 I 最大 200 mA
输出类型 1 至 2 路开关输出 , PNP , 可编程 , 短路保护
UL 认证 cULus 认证,一般用途,2 类电源,1 类外壳
SSI 编码 数字
景深 ± 15 mm
LED 指示 7 个 LED(通信、辅助对齐、状态信息)
数据输出码 格雷码,二进制码 ,可编程
传输速率 38,4 ... 460,8 kBit/s
外壳 PC/ABS
深度 50 mm
“常开位置”速度值 127
功能输入/输出 熄灭
读取距离 80 mm
读取区域 40 mm x 25 mm
查询循环时间 ≥ 1 ms
输入阻抗 26 kΩ
光生物安全性 免除组 根据 EN 62471:2008
抗扰度 EN 61000-6-2:2005
连接类型 8 针 M12 x 1 连接器
出现错误时的 Y 值 错误编号
暂停时间 tp ≥ 20 µs 可进行双重请求,如果 t ≤ 10 µs
时钟脉冲频率 600 MHz
任务时间 (T ) 10 a
接口类型 USB (串行通信端口)
工作温度 0 ... 60 °C (32 ... 140 °F) -20 ... 60 °C (-4 ... 140 °F) 根据请求,可扩展至 -25 °C (无冷凝;防止透镜上结冰!)
相对湿度 90 % ,无冷凝
宽度 70 mm
通过速度 v ≤ 12,5 m/s
MTTF 93 a
诊断覆盖率 (DC) 0 %
开关电压 工作电压
抗振性 EN 60068-2-6:2008
质量 大约 160 g
高度 70 mm
出现错误时的速度值 错误编号
编码带宽度 两行
光源类型 内置 LED 灯 (红)
扫描速率 100 s
工作电压 U 15 ... 30 V DC , PELV
输入类型 1 至 2 路功能输入 , 可编程
CE 符合性 CE
CCC 认证 额定电压 ≤ 36 V 时,产品不需要 CCC 认证/标记
“常开位置”Y 值 0
超速阈值(协议) 12,5 m/s
协议 8E1
分辨率 ± 0,1 mm
UKCA 符合性 UKCA
计算速度 4800 MIPS
防护等级 IP67
X 分辩率(协议) 1 mm
X 位置偏移 0 mm
单稳态触发时间 T = 10 µs
开关电流 150 mA 每个输出
发射干扰 EN 61000-6-4:2007+A1:2011
编码带方向 0 °
出现错误时的 X 值 错误编号
时钟频率 100 ... 1000 kHz
测量范围 最大 10000 m
环境光限制 100000 Lux
功耗 P 3 W
耐冲击性 EN 60068-2-27:2009
存储温度 -25 ... 85 °C (-13 ... 185 °F)
Y 分辩率(协议) 1 mm