安全传感器-视觉传感器/安全传感器-安全传感器品牌厂家-买道传感网官网

商品名称： Pilz 皮尔磁PSEN ma1.3a-20/1switch (526120)PSENmag-非接触式磁性安全开关

商品型号： PSEN ma1.3a-20/1switch (526120)

品牌名： Pilz 皮尔磁

分类：安全传感器

订货号： 526120

类型：安全开关

Approval	CE
传感器可以嵌入式安装	是，黄色安装指南
电源电压类型U1	DC
电缆线路	LiY11Y6x0.25mm2
深度尺寸	59.1mm
海平面以上最大安装高度不受额定功率的限制	4000m
供电电压 (V)	24V
外壳上面部分材质	PBT
在工作高度为2000m时的最高环境温度	+70°C
单元类型	传感器
切换电压	24V
以摄氏度一表示的环境温度	-25-70°C
净重	185g
总重	195g
连接类型	5m电缆
适合串联	否

商品名称： Pilz 皮尔磁PSEN 1.1b-20 /8mm/10m/1switch (524127)PSENmag-非接触式磁性安全开关

商品型号： PSEN 1.1b-20 /8mm/10m/1switch (524127)

品牌名： Pilz 皮尔磁

分类：安全传感器

订货号： 524127

类型：安全开关

单元类型	传感器
外壳上面部分材质	PBT
净重	320g
适合串联	否
以摄氏度一表示的环境温度	-10-70°C
总重	341g
电源电压类型U1	DC
在工作高度为2000m时的最高环境温度	+70°C
连接类型	10m电缆
电缆线路	LiY11Y4x0.25mm2
宽度尺寸	26mm
海平面以上最大安装高度不受额定功率的限制	4000m
深度尺寸	13mm
传感器可以嵌入式安装	是，黄色安装指南
高度尺寸	36mm
Approval	CE
供电电压 (V)	24V
切换电压	24V

商品名称： Pilz 皮尔磁PNOZ XV3.1P 30/24VDC 3n/o 1n/c 2n/o t（777520）PNOZX-安全继电器

商品型号： PNOZ XV3.1P 30/24VDC 3n/o 1n/c 2n/o t（777520）

品牌名： Pilz 皮尔磁

分类：安全传感器

订货号：

类型：安全继电器

以摄氏度一表示的环境温度	-10-55°C
DC1安全控制最大电流	8A
AC15安全控制最大电流	5A
输入的数量	2
功率消耗DC	4.5W
供电电压(V)	24V
Approval	CCC
AC1安全控制最大电流	8A
电源电压类型U1	DC
半导体输出数量	0
AC15安全控制电压	230V
安全触点：导向器负载	C300，R300
AC1安全控制电压	240V
SCIP输入可用	是
继电器的其他触点规格	+0.2µmAu
外壳材料前板	ABSUL94V0
深度尺寸	121mm
净重	510g
DC1安全控制电压	24V
DC13安全控制电压	24V
继电器触点材料	AgSnO2
连接端子	螺丝式端子
总重	520g
高度尺寸	94mm
安装位置	任意
端子样式	可插拔
宽度尺寸	90mm
符合REACh标准	至少含有一种SVHC物质

商品名称： Pilz 皮尔磁 S1PN 400-500VAC 2c/o (890210) PMDsrange-监控继电器

商品型号： S1PN 400-500VAC 2c/o (890210)

品牌名： Pilz 皮尔磁

分类：安全传感器

订货号： 890210

类型：安全继电器

使用类别AC15/DC13标准	EN60947-5-1
继电器的其他触点规格	+3.0µmAu
以摄氏度一表示的环境温度	-15-55°C
EMC达到标准...	EN50082-2
应遵守的间隙与爬电距离标准	EN60947-1
安装位置	任意
功率消耗AC	8VA
高度尺寸	87mm
净重	125g
外壳材料前板	ABSUL94V0
深度尺寸	121mm
供电电压(V)	400-500V
电源电压类型U1	AC
外壳上面部分材质	PPOUL94V0
端子样式	固定式
总重	135g
壳体材料下部	PPOUL94V0
宽度尺寸	22.5mm
设备可使用的气候适宜性标准	EN60068-2-78
振动测试所依据的标准	EN60068-2-6
最大设备断路器	最大导线截面积
连接端子	螺丝式端子
柔性AWG导体的允许截面面积	24-10AWG
使用类别AC/DC1标准	EN60947-4-1
继电器触点材料	AgCdO

商品名称： P+F 倍加福 P-LB-1.A.13 SIL-Capable Products for Hazardous Areas Safety Integrity Level 3

商品型号： P-LB-1.A.13

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：安全栅

Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Marking_1	II 3G Ex nA IIC T4 Gc
Asymmetric	100 ns
IECEx certificate	IECEx BAS 12.0123
Rated voltage	U max. 30 V
IECEx marking	[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I
Series resistor	≤ 0.5 Ω per wire
Rated current	I max. 250 mA
Ground insulation	max. 500 V breakdown voltage
Degree of protection	IP20
Ambient temperature	-20 ... 60 °C (-4 ... 140 °F)
Dimensions	20 x 104 x 127 mm (0.8 x 4.1 x 5 inch) (W x H x D)
Current	I 250 mA
On-state voltage	max. 45 V
Mounting	on the KF module
Bandwidth	≥ 40 kHz
Marking	II (1)G [Ex ia Ga] IIC
Internal capacitance	C negligible
Internal inductance	L 200 µH
Safety Integrity Level (SIL)	SIL 3
Voltage	U 30 V
Connection	terminals 1, 3
Leakage current	max. 5 µA
EU-type examination certificate	PTB 02 ATEX 2044
Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010
Number of protected signal lines	2
Mass	approx. 70 g
Symmetrical	1 ns
Labeling	space for labeling at the front
Certificate	PF 16 CERT 3908 X
Maximum leakage current	10 kA (8/20 µs) per conductor

商品名称： P+F 倍加福 S1SD-1TI-1U 信号调节器 SC-System (DIN rail, compact design)

商品型号： S1SD-1TI-1U

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：隔离栅

Rated voltage	U 16.8 ... 31.2 V DC
Ambient temperature	-25 ... 70 °C (-13 ... 158 °F)
Mass	approx. 70 g
Mounting	on 35 mm DIN mounting rail acc. to EN 60715:2001
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Accuracy	max. 0.1 % of full-scale value
Certificate	DEMKO 16 ATEX 1750X
Measurement loop monitoring	sensor breakage, lead breakage, short circuit
Power dissipation	0.7 W
Operation time	MTBF: 353 a acc. to SN 29500 stationary continuous operating, average ambient temperature 40 °C (104 °F)
Lead resistance	≤ 100 Ω per line
Fault signal	downscale or upscale
Measuring time	≤ 300 ms
Ripple	≤ 10 mV
Power consumption	0.8 W
Connection side	control side
RTD	< 0.1 K/0.05 % of the measured value
Voltage	< 0.1 % of the measured value
Signal type	Analog input
Input resistance	≥ 1 MΩ
Influence of ambient temperature	< 100 ppm/K of full-scale value
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Marking	II 3G Ex nA IIC T4 Gc
Programming interface	programming socket
IECEx certificate	IECEx UL 16.0116X
Measuring current_1	approx. 200 µA
Measurement loop monitoring_1	sensor breakage, lead breakage, short circuit
Height	97 mm
Core cross section	0.5 ... 2.5 mm (20 ... 14 AWG)
Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-15:2010
UL approval	E106378
PTC	type KT, KTY, ST
Types of measuring	2-, 3-, 4-wire connection
Connection	screw terminals
Protection against electrical shock	EN 61010-1:2010
Dimensions	6.2 x 97 x 107 mm (0.24 x 3.82 x 4.21 inch) (W x H x D) , housing type S1
Width	6.2 mm
Storage temperature	-40 ... 85 °C (-40 ... 185 °F)
Measuring current	approx. 200 µA
Measurement loop monitoring_2	sensor breakage, lead breakage
Types of measuring_2	3-wire connection
Analog voltage output	0/1 ... 5 V , 0/2 ... 10 V , load ≥ 2 kΩ
Types of measuring_1	2-, 3-, 4-wire connection
Cold junction compensation	external (Pt100) and internal , manually
Potentiometer	< 0.02 % of the measured value
Input/Other circuits	safe electrical isolation by reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V test voltage 3 kV, 50 Hz, 1 min
Output/power supply	safe electrical isolation by reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V test voltage 3 kV, 50 Hz, 1 min
Analog current output	0/2 ... 10 mA, 0/4 ... 20 mA, load ≤ 600 Ω
Damaging gas	designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
IECEx marking	Ex nA IIC T4 Gc
Configuration	via DIP switches via keys via software
Labeling	space for labeling at the front
Degree of protection	IP20
Depth	107 mm
Lead resistance_1	max. 100 Ω per line
Thermocouples	< 0.3 K/0.1 % of the measured value
Lead resistance_2	max. 10 kΩ
Measuring range	0 ... 5 kΩ

商品名称： P+F 倍加福 HiD2038 SIL-Capable Products for Hazardous Areas Safety Integrity Level 2

商品型号： HID2038

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：隔离栅

Mounting	on termination board
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
IECEx certificate	IECEx ULD 20.0012X
Line fault detection	breakage, load > 100 kΩ, short-circuit, load < 50 Ω
Width	18 mm
Power consumption	≤ 1 W
Rated voltage	U 19 ... 30 V DC bus powered via Termination Board
Dimensions	18 x 114 x 130 mm (0.7 x 4.5 x 5.1 inch) (W x H x D)
Connection side	field side
Input/Output	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Electromagnetic compatibility	NE 21:2017 EN 61326-3-2:2018 For further information see system description.
Output	Ex ia, Ex iaD
Current	I 93 mA
Depth	130 mm
Maximum safe voltage_1	U 250 V (Attention! The rated voltage can be lower.)
Input/input	functional insulation, rated insulation voltage 50 V AC
Degree of protection	IP20
Mass	approx. 140 g
Marking	II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Power dissipation	≤ 1 W at 20 mA and 500 Ω load
Output type	open collector transistor (internal fault bus)
Coding	pin 1 and 3 trimmed For further information see system description.
EU-type examination certificate	DEMKO 20 ATEX 2378 X
Certificate	DEMKO 20 ATEX 2379 X
Marking_1	II 3G Ex ec IIC T4 Gc
Internal capacitance	C 1.05 nF
Directive 2014/34/EU	EN IEC 60079-0:2018 , EN 60079-11:2012 , EN 60079-7:2015+A1:2018
Input voltage	open loop voltage of the control system ≤ 30 V
Labeling	space for labeling at the front
Maximum safe voltage	U 250 V (Attention! The rated voltage can be lower.)
Influence of ambient temperature	< 2 µA/K (-20 ... 70 °C (-4 ... 158 °F)); < 4 µA/K (-40 ... -20 °C (-40 ... -4 °F))
Output/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Protection against electrical shock	UL 61010-1:2012
Deviation	at 20 °C (68 °F), 4 ... 20 mA < 0.1 % of full scale, incl. non-linearity and hysteresis
Frequency range	field side into the control side: bandwidth with 0.5 V signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 0.5 V signal 0 ... 3 kHz (-3 dB)
Ambient temperature	-40 ... 70 °C (-40 ... 158 °F)
Voltage	U 25.2 V
Connection	SL1: 6b
IECEx marking	[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I Ex ec IIC T4 Gc
Load	100 ... 650 Ω , for terminals 1a, 1b; 5a, 5b 0 ... 550 Ω , for terminals 1b, 3b; 5b, 7a
UL approval	E106378
Voltage drop	approx. 6 V at 20 mA
Input signal	4 ... 20 mA , limited to approx. 30 mA
Rated current	I ≤ 40 mA at 24 V
Rise time	10 to 90 % ≤ 10 ms
Power	P 585.3 mW
Input/power supply	basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V
Internal inductance	L 0
Safety Integrity Level (SIL)	SIL 2
Control drawing	116-0475 (cULus)
Signal type	Analog output
Display elements	LEDs
Height	114 mm
Ripple	20 mV rms
Input resistance	field wiring open circuit : > 100 kΩ field wiring < 50 Ω : > 100 kΩ when using terminals 5a, 5b; 1a, 1b

商品名称： P+F 倍加福 HiD2872 SIL-Capable Products for Hazardous Areas Safety Integrity Level 3

商品型号： HiD2872

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：隔离栅

Display elements	LEDs
Signal level	1-signal: 15...30 V DC (current limited to 3 mA) or contact close (internal 10 kΩ pull-up) 0-signal: 0...5 V DC or contact open
Open loop voltage	U approx. 22.5 V
EU-type examination certificate	CESI 10 ATEX 036
Energized/De-energized delay	- bus powered: filter OFF: 1 ms, filter ON: 10 ms - loop powered: switch-on 50 ms, switch-off 6 ms (300 Ω load)
Internal resistor	R approx. 240 Ω
Fault current	4 mA pulsing (20 ms ON, 200 ms OFF)
Mass	approx. 140 g
Dimensions	18 x 114 x 130 mm (0.7 x 4.5 x 5.1 inch) (W x H x D)
Voltage	U 26 V
Output	Ex ia Ga, Ex ia Da, Ex ia Ma
IECEx certificate	IECEx CES 10.0013
Depth	130 mm
Ambient temperature	-20 ... 60 °C (-4 ... 140 °F)
Mounting	on termination board
Switching frequency	f - bus powered: filter OFF: max. 150 Hz, filter ON: max. 15 Hz - loop powered: max. 10 Hz
Certificate	PF 10 CERT 1729 X
Current limit	I 55 mA
Rated voltage	U 20.4 ... 30 V DC loop powered 20.4 ... 30 V DC bus powered via Termination Board
Directive 2014/34/EU	EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010
Input current	62 mA at 24 V, 300 Ω load (per channel)
Current	I 110 mA
Output type	open collector transistor (internal fault bus)
Coding	pin 1 and 4 trimmed For further information see system description.
Safety Integrity Level (SIL)	SIL 3
Marking	II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Control drawing	366-005CS-12B (cCSAus)
Labeling	space for labeling at the front
Height	114 mm
Connection side	field side
Connection	SL1: 6b
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Marking_1	II 3G Ex nA IIC T4 Gc
IECEx marking	[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I
Power	P 715 mW
Output/Output	safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 60 V
Electromagnetic compatibility	NE 21:2006 For further information see system description.
Configuration	via DIP switches
Width	18 mm
Control input	external switch (dry contact or open collector) non isolated or logic signal input fully floating
Relative humidity	5 ... 90 %, non-condensing up to 35 °C (95 °F)
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Signal type	Digital Output
Power dissipation	1 W at 24 V, 300 Ω load (per channel) for loop powered
Maximum safe voltage	U 253 V AC (Attention! U is no rated voltage.)
Control elements	DIP switch
Inrush current	0.2 A , 15 ms loop powered
Fault level	lead short-circuit detection at < 25 Ω lead breakage detection at > 100 kΩ typical
Output/power supply, inputs, and collective error	safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V
Degree of protection	IP20
Load	nominal 0.1 ... 5 kΩ

商品名称： P+F 倍加福 HiC2031HC SIL-Capable Products for Hazardous Areas Safety Integrity Level 2

商品型号： HiC2031HC

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：安全栅

Safety Integrity Level (SIL)	SIL 2
Input voltage	depending on switch configuration open loop voltage of the control system < 19 V open loop voltage of the control system < 26 V
Height	106 mm
Equipment	SL2: 5a(+), 5b(-)
Internal inductance	L negligible
Dimensions	12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D)
Influence of ambient temperature	< 2 µA/K (0 ... 60 °C (32 ... 140 °F)); < 4 µA/K (-20 ... 0 °C (-4 ... 32 °F))
Power consumption	≤ 700 mW
Frequency range	field side into the control side: bandwidth with 0.5 V signal 0 ... 3 kHz (-3 dB) control side into the field side: bandwidth with 1 mA signal 0 ... 3 kHz (-3 dB)
Mass	approx. 100 g
Labeling	space for labeling at the front
Maximum safe voltage	U 253 V AC (Attention! U is no rated voltage.)
Voltage drop	depending on switch configuration open loop voltage of the control system < 19 V: approx. 5 V at 20 mA open loop voltage of the control system < 26 V: approx. 12 V at 20 mA
Power	P 500 mW
Factory setting	input: max. input voltage 19 V
Rated current	I ≤ 35 mA
Power dissipation	≤ 600 mW
Connection side	field side
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Maximum safe voltage_1	U 253 V AC (Attention! The rated voltage can be lower.)
Input signal	4 ... 20 mA , limited to approx. 27 mA
Ripple	20 mV rms
Rated voltage	U 19 ... 30 V DC bus powered via Termination Board
Configuration	via DIP switches
Depth	128 mm
Degree of protection	IP20
Control drawing	116-0393 (cULus)
Signal type	Analog output
Output	Ex ia
IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc
Width	12.5 mm
Internal capacitance	C 5.7 nF
Ambient temperature	-20 ... 60 °C (-4 ... 140 °F)
Input/Output	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Current	I 100 mA
Certificate	CESI 19 ATEX 050 X
Input resistance	> 100 kΩ, with field wiring open
Mounting	on termination board
Marking	II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Electromagnetic compatibility	NE 21:2012 For further information see system description.
Marking_1	II 3G Ex ec IIC T4 Gc
Control elements	DIP switch
Rise time	10 to 90 % ≤ 100 ms
Coding	pin 2 and 4 trimmed For further information see system description.
Deviation	at 20 °C (68 °F), 4 ... 20 mA ≤ ± 0.1 % incl. non-linearity and hysteresis
EU-type examination certificate	CESI 11 ATEX 012
Voltage	U 20 V
Connection	SL2: 5a(+), 5b(-)
Display elements	LED
IECEx certificate	IECEx CES 11.0010X
Load	0 ... 625 Ω
UL approval	E106378
Systematic capability (SC)	SC 3
Input/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V

商品名称： P+F 倍加福 HiC2851 SIL-Capable Products for Hazardous Areas Safety Integrity Level 3

商品型号： HIC2851

品牌名： P+F 倍加福

分类：安全传感器

订货号：

类型：隔离栅

Degree of protection	IP20
Mounting	on termination board
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Height	106 mm
Depth	128 mm
Output II	≤ 50 Hz
Input/power supply	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Lead resistance	max. 50 Ω , consider capacitances and inductances
Switching point	1-signal: I > 2.8 mA 0-signal: I < 2.1 mA
Rated current	I ≤ 55 mA
IECEx certificate	IECEx BAS 07.0097X
Rated voltage	U output II: typ. 8 V DC, max. 22 V DC
Dimensions	12.5 x 106 x 128 mm (0.5 x 4.2 x 5.1 inch) (W x H x D)
Labeling	space for labeling at the front
Line fault detection	breakage I ≤ 0.15 mA , short-circuit I ≥ 8.5 mA
Ripple	≤ 10 %
Output I	≤ 50 Hz
Voltage	U 10.5 V
Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-11:2012 , EN 60079-15:2010
Current	I 17.1 mA
Marking	II (1)G [Ex ia] IIC , [exsign] II (1) D [Ex ia] IIIC , [exsign] I (M1) [Ex ia] I
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Systematic capability (SC)	SC 3
Connection side	control side
Maximum safe voltage_1	U 253 V AC (Attention! U is no rated voltage.)
UL approval	E106378
Coding	pin 1 and 2 trimmed For further information see system description.
Safety Integrity Level (SIL)	SIL 3
Control drawing	16-534FM-12 (cFMus)
Signal type	Digital Input
Input/Output	safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Output/Output	functional insulation acc. to IEC 62103, rated insulation voltage 50 V
Certificate	PF 09 CERT 1440 X
Control drawing_1	116-0364
Input	Ex ia
Output/power supply	functional insulation acc. to IEC 62103, rated insulation voltage 50 V
Ambient temperature	-20 ... 60 °C (-4 ... 140 °F)
Mass	approx. 105 g
Power dissipation	≤ 800 mW
Connection	SL1: 6b
Switching point/switching hysteresis	2.1 ... 2.8 mA / approx. 0.3 mA
Electromagnetic compatibility	EN IEC 61326-3-2:2018 , NE 21:2017 For further information see system description.
Maximum safe voltage	U 253 V AC (Attention! U is no rated voltage.)
Marking_1	II 3G Ex nA IIC T4 Gc
IECEx marking	[Ex ia Ga] IIC, [Ex ia] IIIC , [Ex ia] I
Open circuit voltage/short-circuit current	approx. 8.4 V DC / approx. 11.9 mA
Response delay	≤ 1 ms
Power	P 45 mW (linear characteristic)
Power consumption	≤ 1300 mW
EU-type examination certificate	BASEEFA 07 ATEX 0302X
Display elements	LEDs
Width	12.5 mm
Output type	open collector transistor (internal fault bus)